Where Does A Breather Filter Go 2.4l Gdi Engine
Kia Sorento 3.3L V6 Engine Oil Change Guide
How to change the motor oil and filter on the Lambda II 3.3L V6 engine in a 3rd generation 2016 to 2020 Kia Sorento.
2019 Sorento 3.3L V6
Oil Filler Cap Location
Spin Off Counterclockwise
This automotive maintenance tutorial was specifically written to assist owners of the tertiary generation (2016, 2017, 2018, 2019 and 2020) Kia Sorento SUV in changing the motor oil and replacing the cartridge way oil filter on the Lambda Two GDI 3.iii liter V6 engine. (The procedure may exist like for the Theta II ii.4L I4 engine and the Theta II Turbocharged 2.0L I4 engine.)
Owners of other Kia, Hyundai and Genesis vehicles such as the Soul, Seltos, Sportage, Niro, Telluride, Forte, Rio, Optima, Stinger, Cadenza, K900, Sedona, Kona, Venue, Santa Fe, Elantra, Sonata, Accent, Veloster, Ioniq, Nexo, G70, G80 and G90 may also find these instructions to be helpful.
A few compatible replacement cartridge fashion oil filters for the 2016, 2017 and 2018 model years with the Lambda II GDI 3.3L V6 engine are as follows: Wix WL10164, Fram CH10855 and Purolator PL26127.
A few compatible replacement cartridge style oil filters for the revised 2019 and 2020 model years with the Lambda II GDI 3.3L V6 engine with their part numbers are as follows: Wix WL10033, Fram CH11934 and Purolator L18179.
( Annotation - Amazon may show that the oil filters listed above for the 2019 and 2020 model years do not fit. I triple checked the office numbers at the manufacturers' websites and several automobile parts stores. They are right.)
The tools and other items needed to consummate this procedure include a floor jack with two jack stands (or automotive service ramps), a 10mm socket with a 1/4" drive ratchet, a 17mm socket with a iii/8" drive ratchet, a 27mm socket with a one/2" bulldoze ratchet, a used oil grab container and an automotive funnel.
Attention - Please cheque the "Recommended Lubricants and Capacities" section of your owner's manual for the oil chapters specification for your vehicle for an oil change with a filter replacement.
For this 2019 Kia Sorento with the 3.3L V6, the possessor'southward manual lists the oil chapters for a drain and refill with a new oil filter as being vi.87 U.Southward. quarts (or half dozen.v liters).
The owner'south manual for a 2017 Sorento lists 6.02 U.Due south. quarts as the capacity for a drain and refill with a filter replacement.
This 2019 Sorento 3.3L V6 requires that you purchase 7 quarts of new SAE 5W-30 oil to complete an oil change.
If you have an older tertiary generation model, you could just buy 6 quarts since the chapters is half dozen.02 U.S. quarts.
The first steps are to warm up the engine for a few minutes, drive the SUV on to a level surface and turn off the ignition.
Warming up the engine volition assist append any contaminants or debris within the old oil and likewise permit it to drain out more rapidly.
Shift the transmission into park and appoint the emergency / parking brake to aid forbid the vehicle from moving.
I'd also recommend placing wheel chocks on both sides of the rear tires to further reduce the chance of the vehicle moving unexpectedly.
Spin off the oil filler cap and set up information technology bated in a safe place.
Partially Remove Dipstick
Under Engine Cover
Loosen Bolts
Removing the oil filler cap and partially lifting the dipstick will help prevent a vacuum from forming which will allow the old oil to drain out more apace.
You might exist able to squeeze under the SUV to access the drain bolt and oil filter. I institute it necessary to enhance the SUV.
Carefully raise the front of the SUV with the flooring jack and deeply support it with at least two jack stands.
You lot could also instead utilize automotive service ramps.
Delight do not solely rely on the floor jack to support the vehicle!
Remove Skid Plate
Slide Back Encompass
Bolts Removed
Set the bolts aside in a safe place.
Pull off the under engine cover and slide it back towards the rear of the vehicle.
Black Metal Oil Pan
Black Plastic Filter Housing
Used Oil Catch Container
Slide the used oil take hold of basin to only below the oil drain bolt.
Oil Drain Commodities - Rear
Loosen Counterclockwise
Draining Out Old Oil
Loosen the oil drain bolt in the counterclockwise direction with the 17mm socket and a 3/8" drive ratchet.
Advisedly spin out the drain plug the residuum of the style by hand.
Permit the sometime oil to drain out for at least a few minutes or until the menstruation slows downward to merely an occasional drip.
Audit the metal washer or "gasket" on the oil drain commodities and replace it if necessary.
The OEM function number for the oil bleed bolt washer isKia # 21513-23001 (also known as 2151323001).
Make sure that the old bleed bolt washer is not yet attached to the oil pan.
Slide the new washer over the bleed bolt. Clean the expanse effectually the oil drain pigsty with a paper towel or a shop rag.
Tighten Oil Drain Commodities
Large 27mm Socket
Hex Head Filter Housing
Spin in the oil drain bolt a few turns by mitt in the clockwise direction to prevent it from becoming cross threaded.
Tighten the oil drain commodities with the 17mm socket and a 3/8" drive ratchet until it is snug.
If you have atorque wrench, the service manual specifies that the oil drain bolt torque specification is 25.three to 32.5 lb-ft (34.iii to 44.1 Nm).
Attach the 27mm socket to a 1/ii" bulldoze ratchet.
Loosen Counterclockwise
Draining Out Old Oil
Replace Filter - Tighten
Loosen the oil filter cap by turning information technology in the counterclockwise direction with the 27mm socket and the one/two" bulldoze ratchet.
Permit the onetime oil to bleed out from the loosened filter cap for a infinitesimal or 2 before you lot fully remove it.
The next few steps were messy and I did not take pictures.
Pull the old cartridge oil filter element out of the filter cap and discard it.
Pry the old condom o-ring off the oil filter cap with a flat head screwdriver and discard it.
Apply a pocket-sized corporeality of new oil to the new rubber o-band that was included with the new oil filter.
Button the new o-ring downward over the threads dorsum into position on the filter cap. Make sure the o-ring is properly seated.
Lubricating the prophylactic o-ring or "gasket" will help the filter cap class a better seal, forestall oil leaks and also making it easier to remove the cap during the next oil modify.
Button the new filter chemical element into the cap until it "clicks" securely into place.
Insert the filter into the housing and spin in the cap a few turns by mitt in the clockwise direction until it is snug or about one/four to 1/2 turn past finger tight.
If you lot have a torque wrench, tighten the oil filter cap to 25.eight lb-ft of torque (35 Nm).
Slide Forward Cover
Re-Install Skid Plate
Spin In Bolts
Raise the under engine cover back into place.
Spin in the bolts a few turns past hand in the clockwise direction to help prevent them from condign cross threaded.
Tighten Bolts Clockwise
Lower Automobile From Stands
Insert Automotive Funnel
If you raised the vehicle, carefully lower it from the jack stands by using the floor jack.
Insert the automotive funnel into the oil filler hole.
Attention - Please check the "Recommended Lubricants and Capacities" department of your possessor's manual for the oil capacity specification for your vehicle for an oil change with a filter replacement.
For this 2019 Kia Sorento with the three.3L V6, the owner'due south transmission lists the oil capacity for a bleed and refill with a new oil filter as beingness 6.87 U.Due south. quarts (or 6.5 liters).
The owner's manual for an earlier 2017 Sorento lists half-dozen.02 U.S. quarts as the capacity for a drain and refill with a filter replacement.
Delight double check your possessor's transmission before filling the engine with oil!
Pour In New Oil
Replace Oil Fill Cap
Push button Downwardly Dipstick
Running an engine that has been over filled with oil may cause sluggish performance and possibly damage seals, gaskets or other components.
I recommend at first only pouring in well-nigh lxxx% to xc% of the engine's oil capacity for an oil change with a filter replacement.
So for this 2019 Sorento with a "drain and refill" capacity of half-dozen.87 U.S. quarts, I started past only pouring in about 6 U.Due south. quarts of new SAE 5W-xxx oil.
And then temporarily replace the oil filler cap past twisting it on in the clockwise direction and push downwards the dipstick handle back into place.
Start the engine and allow it to warm up to almost operating temperature for a few minutes.
Then plough off the ignition and allow the new oil to bleed back down to the oil pan for at least xv minutes.
Check Oil Level - F 50
Replace Dipstick
Oil Change Complete!
If necessary, slowly cascade in more than new oil and repeatedly check the level on the dipstick until it reaches at or only below the dot next to the "F" which indicates the "Full" or "Maximum" line.
Once the oil level is right, replace the dipstick and twist on the oil filler cap in the clockwise direction until it is snug.
If your vehicle is equipped with the service indicator system, you can reset the oil life past post-obit these steps: 1. Plow the ignition switch to the "ON" position but exercise non kickoff the engine. ii. When you hear the chime and see the "Wrench" service icon, printing and concord the "OK" button to reset the oil change service interval.
If you lot haven't previously setup the oil life function, yous may run into "Service Interval Off" on the instrument cluster'southward LCD screen.
If your Sorento has the small LCD display screen in the speedometer, follow these steps: ane. Plough the ignition switch to "ON" just practise non beginning the engine. For the push push button "First" simply don't put your foot on the brake pedal. 2. Navigate to "User Settings" in the menu. 3. Choose "Service Interval". 4. Cull "Reset". 4. When y'all see "Reset fourth dimension and altitude?" - choose "Yes".
You can too arrange the "service interval" (miles / KM / months) in the settings bill of fare.
I recommend checking your parking spot, garage or driveway for drops of fresh oil over the next few days to make sure there isn't a leak from the drain bolt or filter cap.
Information technology would also be a proficient thought to check the oil level after a few days (when the engine is cold) and at least once a month in the future.
Be sure to tape the oil alter in your SUV's service records.
The service interval specification in the owner'southward transmission for this 2019 Sorento is to alter the oil and filter every seven,500 miles (12,000 KM) or every 12 months.
Delight have a await at all of my 2016-2020 Kia Sorento DIY Repair & Maintenance Guides.
Where Does A Breather Filter Go 2.4l Gdi Engine,
Source: https://www.paulstravelpictures.com/2016-2020-Kia-Sorento-Lambda-II-GDI-V6-Engine-Oil-Change-Guide/index.html
Posted by: robinsongropen.blogspot.com
0 Response to "Where Does A Breather Filter Go 2.4l Gdi Engine"
Post a Comment